Skip to Content

Skure-Tech S4

Skure-Tech S4

Perfect construction technique. Simplicity in application of the plaster (mortar). Express application of the plaster. Efficient for use.

Technical characteristics:

1. Application rate up to 22 l/min

2. Horizontal hose reach up to 40 m

3. Vertical hose reach up to 20 m

4. Mains power requirements 400/50 V/Hz

5. Main mixing engine 5.5 kw

6. Application motor 0.55 kw

7. Water pump 0,33 kw – 230 V

8. Compressor 250 l/min

9. Water pressure min. 2 bars

10. Air pressure max. 5 bars

Equipment domensions:

1. Maximum height 151 cm

2. Depth 73 cm

3. Width 112 cm

4. Extended height 90 cm

Instructions for use  PDF

Skuretech-S4 User Manual


READ MORE

Metal protective skirting boards

These are made from sheet of zinc alloy in accordance with the EU standards 101142/101143 DX51D. The thickness of the sheet metal is either 0,42 mm or 0,50 mm. The length of the skirting boards is standard (2,70 m and 2,80 m). Orders can be accomodated from 1,80 m to 4,00 m. These can be used for both exterior and interior surfaces.
On the basis of chemical and mechanical research, the material from which the scirting boards are made is equal to steel with quality of EN TC01 (ISO 630-80; DIN ST12; JUS C 0270), from the group of consrtuctive steels for common use.

READ MORE

Renofix 01 – Bоnding (BETONKONTAKT)

RENOFIX 01

Plaster adhesive, bonding agent for plaster and cement plaster on smooth concrete surface. 20 kg primer must be diluted with water and ½ iter dan well with whisk

Stir, dan underline the wall or roll, after 24 hours you can apply.Do not work under temperature +5 ° C.

READ MORE

Renogrund – Primer for interior and exterior

RenoGround

Renogrund – Primer for interior and exterior.

Ready-pigmented primer with mineral fillers. Universal primer to equalize and additional waterproofing or Varies greatly absorbent substrates. Primer for subsequent coating with mineral, silicate or emulsion plasters. The Renogrund primer prepares the ground up so that it is ideally suited for the application of paste finishing coats.

This product is a baseline for previously plastered surfaces or basic plasters such as cement,gypsum or lime.It can be a bonding material for plastic plasters.24 hours after spreading Renogrund plastic plasters can be applied.

Consumption : 200g/m2pro coating on smooth surfaces.

READ MORE

Renocolor Classic

RenoColor

Composition: Water based dispersion paint Application: Final protection decorative inerior wall/celling paint. Before use dilute with cca 20% of water and stir well Storage: cca 0,25 L/m2

Storage: drying store at +5°C to +25°C.

Protect: against frost!

Durability: 18 month in original package

READ MORE

FasadenFarbe – High quality color for beautiful facades

Fasaden Farbe

Outdoor use (facades) and indoors when Renofix. Strukture and decorative plasters were used. Applied by brush, roller or compressed air.

For all exterior wall surfaces, resistant to abrasion, excellent coverage.

Use: Dilute color with 5% clean water,

Consumption: 0.20 L/m2.

Storage: Store in dry conditions at temperatures +5 ° С to +25 ° С.

Shelf life: 18 months in original packaging, protected from frost.

READ MORE

MINERAL WOOL

1.RENOFIX 5

Glue for plate

2.PLATE OF MINERAL WOOL

Mineral, inflamable

3.RENOFIX 41, PLASTER FOR NET GLUING

Levelling with minimal thickness of 6 mm

4.RENOFIX G40, REINFORCED NET

Alkaline resistant, elastic

5.RENOFIX 5 WHITE

Baseline for mineral plasters

6.RENOFIX 370 0,5 / 1 / 1,5 / 2 / 3 mm

RENOFIX 700 0,5 / 1 / 1,5 / 2 / 3 mm

READ MORE

POLYSTYROL

1.RENOFIX 5, CEMENT CONSTRUCTIVE GLUE

Glue for plate

2.POLYSTYROL PLATE

Fire retardent

3.RENOFIX 5 WHITE, CEMENT CONSTRUCTIVE GLUE

Glue for levelling

4.RENOFIX G50, REINFORCED NET

Toxic resistant, elastic

5.RENOFIX 370 0,5 / 1 / 1,5 / 2 / 3 mm

RENOFIX 700 0,5 / 1 / 1,5 / 2 / 3 mm

READ MORE

Renofix 66 GRAY – LIGHT PERLIT PLASTER FOR FAÇADE AND INTERNAL WALLS WITH TERMOISOLATION

Light perlit plaster for façade, interior and exterior walls. For manual plastering 1 sack of Renofix 66 is mixed with 8 to 9 litres of clean water for 2 minutes and spread with sand. The Skure-Tech S4 is used for machine plastering. The area of the walls must be cleaned from dust, waste and grease. On smooth concrete areas Renofix 5 construction glue must be used as a joint plaster. The minimum thickness is 10 mm. Do not mix with other materials. The minimum functional temperature is 5°C. Product will expire after 6 months. Store in a dry place. Ensure the technical manual is followed.

Technical Sheet

Renofix-66

READ MORE

Renofix 200 WHITE – SMOOTHING MATERIAL (WHITE PLASTER) FOR LEVELLING (SMOOTHING) INTERIOR WALLS AND CEILINGS

The mixture for sanding walls previously plastered or constructed from gypsum plasterboard. One sack Renofix 200 is mixed in 12-13 litres of water. Remains able to be spread for 40 to 50 minutes. The thickness of the plaster should be 1-5 mm. The wall plastered with Renofix 200 allows for 2,5% moisture, but before applying wall-paper or colour must be completely dry. The minimum functional temperature is 5°C.

Technical Sheet

RENOFIX-200

READ MORE

Renofix 220 GRAY – LIGHT PLASTER FOR TREATMENT OF INTERNAL WALLS WITH PERLIT

Light layer of lime baseline for ceilings and internal concrete walls. One sack of Renofix 220 is poured into 10 to11 litres of water and is mixed. The Skure-Tech S4 is used for machine plastering afterwards levelling is required as is sanding. The thickness of the plaster should be 8 to 10 mm. The minimum functional temperature is 5°C. Do not mix with other materials. Store in a dry place.

Technical Sheet

RENOFIX-220

READ MORE

Renofix 202 – SAND LAYER WITH LIME BASELINE FOR LEVELLING/SANDING

A sand layer, for levelling (sanding) internal wall areas, previously plastered with basic plaster (gypsum/lime/cement) and gypsum plasterboard. One sack of Renofix 202 is poured slowly into 12 to 13 litres of clean water and is mixed. The material should be free of lumps and is then spread with a trowel. The thickness of the plaster should be from 1 to 5 mm. The minimum functional temperature is 5°C.

Technical Sheet

Renofix-202

READ MORE